YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMSV type motor >> SGMSV-15ADA6E servo motor

SGMSV-15ADA6E servo motor

Yaskawa SGMSV-15ADA6E Manual And Instructions
SGMSV-15ADA6E Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMSV-15ADA6E Product information and technical parameters:
Brand: Yaskawa
Name: servo motor
Model: SGMSV-15ADA6E
Sigma -V series servo motor SGMSV.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

SGMMV type of small capacity servo motor.
Rated output: 10W.
Voltage: AC200V.
Serial encoder: 17 bit absolute value type.
Design sequence: standard.
Shaft end: straight (standard).
Optional parts: with brake.
Ultra small, ultra small capacity
Flange size 15mm:3.3 ~ 11W.
Flange size 25mm:10 ~ 30W.
Is equipped with a high resolution absolute value serial encoder (17 bit) SGMSV-15ADA6E.
Can also be used as an incremental SGMSV-15ADA6E
Max speed up to 6000r/min.
Type is complete (there are 2 kinds of flange size, DC/AC power supply voltage, with hold brake).











Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor) SGMSV-15ADA6E.
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time SGMSV-15ADA6E.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Full closed loop module.
Maximum applicable motor capacity: 5.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMSV-15ADA6E.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMSV-15ADA6E.
External encoder capable of corresponding high resolution (linear grating).


...More relevant models >>>>