Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMJV type motor
>> SGMJV-08AAAB1 Middle inertia rotary servo motor
SGMJV-08AAAB1 Middle inertia rotary servo motor
Yaskawa SGMJV-08AAAB1 Product information and technical parameters：
Brand: Yaskawa
Name: Middle inertia rotary servo motor
Model: SGMJV-08AAAB1
Sigma -V series servo motor SGMJV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 13 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: no matching.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13\/20 bit).
Max speed up to 6000r\/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMJV-08AAAB1 SGMJV-08AAAB1
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMJV-08AAAB1.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMJV-08AAAB1. High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specification: base mounting type (standard).
Interface: analog voltage, pulse sequence type (rotary servo motor).
Function: no deviation standard.
High performance sigma shaped -V-EX series.
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMJV-08AAAB1.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMJV-08AAAB1.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMJV-08AAAB1 SGMJV-08AAAB1
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMJV-08AAAB1.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMJV-08AAAB1. High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specification: base mounting type (standard).
Interface: analog voltage, pulse sequence type (rotary servo motor).
Function: no deviation standard.
High performance sigma shaped -V-EX series.
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMJV-08AAAB1.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMJV-08AAAB1.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa Middle inertia rotary servo motor SGMJV-06AAAB1
next one: Yaskawa Middle inertia rotary servo motor SGMJV-A5AAABC
Related download