Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMJV type motor
>> SGMJV-04A3A61 Middle inertia rotary servo motor
SGMJV-04A3A61 Middle inertia rotary servo motor
Yaskawa SGMJV-04A3A61 Product information and technical parameters：
Brand: Yaskawa
Name: Middle inertia rotary servo motor
Model: SGMJV-04A3A61
Sigma -V series servo motor SGMJV.
Rated output: 0.4KW (400W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
Large capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMJV-04A3A61 SGMJV-04A3A61
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor SGMSH type SGMJV-04A3A61.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGMJV-04A3A61.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMJV-04A3A61.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMJV-04A3A61.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
Rated output: 37KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMJV-04A3A61 SGMJV-04A3A61
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor SGMSH type SGMJV-04A3A61.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGMJV-04A3A61.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMJV-04A3A61.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMJV-04A3A61.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
...More relevant models >>>>
Last one: Yaskawa Middle inertia rotary servo motor SGMJV-02A3A61
next one: Yaskawa Middle inertia rotary servo motor SGMJV-06A3A61
Related download