Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMGV type motor
>> SGMGV-75ADC2E Rotary servo motor
SGMGV-75ADC2E Rotary servo motor
Yaskawa SGMGV-75ADC2E Manual And Instructions
SGMGV-75ADC2E Setup Rotational MotorProduct Manual
Yaskawa SGMGV-75ADC2E Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-75ADC2E
Sigma -V series servo motor SGMGV.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMGV-75ADC2E Setup Rotational MotorProduct Manual
Yaskawa SGMGV-75ADC2E Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-75ADC2E
Sigma -V series servo motor SGMGV.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Key: straight shaft end uranium belt with screw.
Optional parts: no brake oil seal.
Ultra high power response series: the need for small inertia, high torque SGMGV-75ADC2E.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGMGV-75ADC2E
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals SGMGV-75ADC2E.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorLarge capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGV-75ADC2E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMGV-75ADC2E.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMGV-75ADC2E.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Key: straight shaft end uranium belt with screw.
Optional parts: no brake oil seal.
Ultra high power response series: the need for small inertia, high torque SGMGV-75ADC2E.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGMGV-75ADC2E
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals SGMGV-75ADC2E.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorLarge capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGV-75ADC2E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMGV-75ADC2E.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMGV-75ADC2E.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
...More relevant models >>>>
Last one: Yaskawa Rotary servo motor SGMGV-55ADC2E
next one: Yaskawa Rotary servo motor SGMGV-1AADC2E
Related download