YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMGV type motor >> SGMGV-20DDA21 Rotary servo motor

SGMGV-20DDA21 Rotary servo motor

Yaskawa SGMGV-20DDA21 Manual And Instructions
SGMGV-20DDA21 Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMGV-20DDA21 Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20DDA21
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication SGMGV-20DDA21.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMGV-20DDA21 Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time SGMGV-20DDA21.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGV-20DDA21. Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSecurity module.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechannical systems SGMGV-20DDA21.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other itemms can be changed through the parameter SGMGV-20DDA21.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized.


...More relevant models >>>>