YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDM series >> SGMGH type servo motor >> SGMGH-40ACB2S servo motor

SGMGH-40ACB2S servo motor


Yaskawa SGMGH-40ACB2S Product information and technical parameters:
Brand: Yaskawa
Name: servo motor
Model: SGMGH-40ACB2S
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control

Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load SGMGH-40ACB2S.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGH-40ACB2S
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity SGMVV type servo motor SGMGH-40ACB2S.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGH-40ACB2S.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Innstallation method: flange type SGMGH-40ACB2S.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-40ACB2S.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>
Related download