Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMGH type servo motor
>> SGMGH-30ACC3C Motor for high precision machine tool
SGMGH-30ACC3C Motor for high precision machine tool
Yaskawa SGMGH-30ACC3C Product information and technical parameters：
Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-30ACC3C
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMGH-30ACC3C.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMGH-30ACC3C
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGMGH-30ACC3C. Servo motor type SGMPH (speed: 3000r\/min).
Power: 1.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal SGMGH-30ACC3C.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedSigma -V series servo motor SGMPS.
Rated output: 400W (0.4KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Innstallation method: flange type SGMGH-30ACC3C.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC3C.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMGH-30ACC3C.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMGH-30ACC3C
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGMGH-30ACC3C. Servo motor type SGMPH (speed: 3000r\/min).
Power: 1.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal SGMGH-30ACC3C.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedSigma -V series servo motor SGMPS.
Rated output: 400W (0.4KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Innstallation method: flange type SGMGH-30ACC3C.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC3C.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Motor for high precision machine tool SGMGH-20ACC3C
next one: Yaskawa Motor for high precision machine tool SGMGH-44ACC3C
Related download