YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMAV type motor >> SGMAV-01ADA2S Ultra low inertia servo motor

SGMAV-01ADA2S Ultra low inertia servo motor

Yaskawa SGMAV-01ADA2S Manual And Instructions
SGMAV-01ADA2S Setup Rotational MotorCommand Manual

Yaskawa SGMAV-01ADA2S Product information and technical parameters:
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-01ADA2S
Sigma -V series servo motor SGMAV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot,
Handling machinery,
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specification: base mounting type (standard).
Interface: MECHATROLINK-III communication command type (linear servo motor) SGMAV-01ADA2S.
Function: no deviation standard.
High performance sigma shaped -V-EX series SGMAV-01ADA2S
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control SGMAV-01ADA2S. Sigma -V series servo motor SGMGV.
Rated output: 11kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed) SGMAV-01ADA2S.
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specification: base mounting type (standard).
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series.
2 models of high performance seervo unit SGMAV-01ADA2S.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved. SGMAV-01ADA2S.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control.


...More relevant models >>>>