YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____15 Type (Used by linear servo motor) >> SGDV-590A15B Servo driver for linear servo motor

SGDV-590A15B Servo driver for linear servo motor

Yaskawa SGDV-590A15B Manual And Instructions
SGDV-590A15B MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-590A15B Design and MaintenanceUSER'S MANUAL

Yaskawa SGDV-590A15B Product information and technical parameters:
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-590A15B
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Full closed loop module.
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) SGDV-590A15B.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGDV-590A15B
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response SGDV-590A15B.
External encoder capable of corresponding high resolution (linear grating). SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 25N.
Servo motor outside diameter size: 175mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side.
Optional specifications: no matching SGDV-590A15B.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flaange type SGDV-590A15B.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-590A15B.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>