YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____15 Type (Used by linear servo motor) >> SGDV-1R9D15B002000 Servo driver for linear servo motor

SGDV-1R9D15B002000 Servo driver for linear servo motor

Yaskawa SGDV-1R9D15B002000 Manual And Instructions
SGDV-1R9D15B002000 MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-1R9D15B002000 Design and MaintenanceUSER'S MANUAL

Yaskawa SGDV-1R9D15B002000 Product information and technical parameters:
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-1R9D15B002000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.6Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load SGDV-1R9D15B002000.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-1R9D15B002000
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMSV SGDV-1R9D15B002000.
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGDV-1R9D15B002000.
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSigma -V series servo motor SGMGV.
Rated output: 4.4kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat rresistance grade: F SGDV-1R9D15B002000.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-1R9D15B002000.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>