SGDV-120D25B002000 Servo driver for linear servo motor

YaskawaServo driver for linear servo motorSGDV-120D25B002000

SGDV-120D25B002000 Introduce | SGDV-120D25B002000 Catalog / Manual / Instructions / Software download

Yaskawa SGDV-120D25B002000 Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-120D25B002000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 1.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
Ultra high power response series: the need for small inertia, high torque SGDV-120D25B002000.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGDV-120D25B002000
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals SGDV-120D25B002000.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorFull closed loop module.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) SGDV-120D25B002000.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating). Large capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: with dust.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGDV-120D25B002000.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen

...More relevant models >>>>