Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMGH type servo motor
>> SGMGH-09ACD2S Motor for high precision machine tool
SGMGH-09ACD2S Motor for high precision machine tool
Yaskawa SGMGH-09ACD2S Product information and technical parameters：
Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-09ACD2S
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Large capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGH-09ACD2S.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products SGMGH-09ACD2S
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSecurity module SGMGH-09ACD2S.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module SGMGH-09ACD2S.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Full closed loop module.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGH-09ACD2S.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMGH-09ACD2S.
External encoder capable of corresponding high resolution (linear grating).
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGH-09ACD2S.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products SGMGH-09ACD2S
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSecurity module SGMGH-09ACD2S.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module SGMGH-09ACD2S.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Full closed loop module.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGH-09ACD2S.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMGH-09ACD2S.
External encoder capable of corresponding high resolution (linear grating).
...More relevant models >>>>
Last one: Yaskawa Motor for high precision machine tool SGMGH-03ACD2S
next one: Yaskawa Motor for high precision machine tool SGMGH-12ACD2S
Related download