YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGD7S/SGD7W series >> SGM7J type servo motor >> SGM7J-A5A7C6S Rotary servo motor

SGM7J-A5A7C6S Rotary servo motor

Yaskawa SGM7J-A5A7C6S Manual And Instructions
SGM7J-A5A7C6S datasheetPDF datasheet
SGM7J-A5A7C6S INSTRUCTION SHEET

Yaskawa SGM7J-A5A7C6S Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGM7J-A5A7C6S
No speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal.
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tuning time to ensure performance.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possible to detect and prevent failure.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure

Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Optional (hardware): DB resistance external type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGM7J-A5A7C6S SGM7J-A5A7C6S
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGM7J-A5A7C6S.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGM7J-A5A7C6S. Sigma -V series servo motor SGMJV.
Rated output: 0.4KW (400W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot,
Handling machinery,
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Insstallation method: flange type SGM7J-A5A7C6S.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGM7J-A5A7C6S.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.


...More relevant models >>>>