YASKAWA
Home >> Download >> Yaskawa >> Manual Download >> SGM7G-09AFC6E Installation Guide ()

SGM7G-09AFC6E Installation Guide ()

Brand: Yaskawa
Product model: SGM7G-09AFC6E
Name: Safety Network Controller
Sort: Installation Guide
File language: English
File size: 21.92MB
Full closed loop module.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) SGM7G-09AFC6E Installation Guide.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGM7G-09AFC6E
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response SGM7G-09AFC6E Installation Guide.
External encoder capable of corresponding high resolution (linear grating). Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load SGM7G-09AFC6E Installation Guide.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMGV.
Rated output: 300W (0.3kw).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat ressistance grade: F SGM7G-09AFC6E Manual.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGM7G-09AFC6E Manual.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Related products
Yaskawa
Medium inertia, large torque servo motor
SGM7G-05AFC6E
Yaskawa Medium inertia, large torque servo motor SGM7G-05AFC6E
No speed reducer in inertia, large torque ser
Yaskawa
Medium inertia, large torque servo motor
SGM7G-30A7C61
Yaskawa Medium inertia, large torque servo motor SGM7G-30A7C61
No speed reducer in inertia, large torque ser
Yaskawa
Medium inertia, large torque servo motor
SGM7G-13AFC61
Yaskawa Medium inertia, large torque servo motor SGM7G-13AFC61
No speed reducer in inertia, large torque ser
Yaskawa
Medium inertia, large torque servo motor
SGM7G-1AA7C6S
Yaskawa Medium inertia, large torque servo motor SGM7G-1AA7C6S
No speed reducer in inertia, large torque ser